NOTE: To be safe always unplug controller from a “hot port” when vehicle is stored outside in adverse weather conditions or in a parking garage near heavy construction. THESE SITUATIONS TYPICALLY WILL cause vehicle rocking or vibration movement. If not unplugged the PLD could drain vehicle battery over a period of time.
Care and Maintenance
Your Lightfilm™ product is a product of superior design & craftsmanship and should be treated with care. The suggestions below will help you fulfill any warranty obligations and allow you to enjoy this product for many years.
- Keep the Lightfilm™ product and all its parts and accessories out of the reach of small children.
- Keep the Lightfilm™ product dry. Precipitation, humidity and liquids contain minerals that will corrode electronic circuits.
- Do not touch the Lightfilm™ product with a wet hand. Doing so may cause an electric shock to you or damage to the Lightfilm™ product.
- Do not use or store the Lightfilm™ product in dusty, dirty areas, as its moving parts may be damaged.
- Do not store the Lightfilm™ product in cold areas. When the Lightfilm™ product warms up to its normal operating temperature, moisture can form inside the Lightfilm™ product, which may damage the Lightfilm™ product's electronic circuit boards.
- Do not store the Lightfilm™ product in hot areas. High temperatures can shorten the life of electronic devices, damage power adapters, and warp or melt certain plastics.
- Do not drop, knock or shake the Lightfilm™ product. Rough handling can break internal circuits.
- Do not use harsh chemicals, cleaning solvents or strong detergents to clean the Lightfilm™ product. Wipe it with a soft cloth slightly dampened in a mild soap-and-water solution.
- Do not paint Lightfilm™ products. Paint can clog the moving parts & prevent proper operation.
- Do not put the Lightfilm™ product in or on heating devices, such as a microwave oven, a stove or a radiator. The Lightfilm™ product may explode when overheated.
Frequently Asked Questions
Q1. Controller power LED (amber colored LED) does not work when I plug Controller into selected vehicle 12 volt port?
A1. This could mean the 12 volt port only receives power when the vehicle ignition is turned on. Or, the Controller fuse needs replacement. The fuse is located in the front pin area of Controller (unscrew cap, remove fuse and check fuse element visually) replace if necessary. Replacement fuses (2 Amp) are readily available at many automotive parts retailers.
Q2. Controller amber color LED works but green color LED doesn’t light up?
A2. This means your Controller has power; however sensors do not detect darkness and vehicle motion. To test, simply cover the light sensor (Clear LED) with black tape (to obstruct ambient light) and tap the Controller housing to simulate motion, the green LED should light up accordingly.
Q3. Controller amber AND green LEDs work, but my PLD panel doesn’t light up?
A3. Make sure the panel cord is fully engaged into Controller component.
Q4. PLD will never shut off?
A4. This could mean the Controller is plugged into a “hot port” and is also sensing outside related motion effecting vehicle like: wind storms or thunder storms and super heavy rains during night duration (darkness) or parked inside garage near heavy construction. NOTE: To be safe always unplug controller from a “hot port” when vehicle is stored outside in adverse weather conditions or in a parking garage near heavy construction. THESE SITUATIONS TYPICALLY WILL cause vehicle rocking or vibration movement. If not unplugged the PLD could drain vehicle battery over a period of time.
Q5. PLD cable is too short?
A5. Purchase the appropriate accessory extension cables. Or relocate panel near Controller.
WARNING: Never route PLD power cable through
vehicle air bag deployment area(s).
This could result in serious injury.
Safety & General Information
IMPORTANT INFORMATION ON SAFE OPERATION.
READ THIS INFORMATION BEFORE USING YOUR LIGHTFILM™ PRODUCT
Safety Tips While Driving
When driving a car, driving is your first responsibility. It is the sole responsibility of the driver of the vehicle to operate the vehicle in a safe manner, maintain full surveillance of all driving conditions at all times, and not become distracted by the Lightfilm™ products to the exclusion of safe driving practices. Failure by the driver of a vehicle equipped with Lightfilm™ products to pay full attention to operation of the vehicle and road conditions while the vehicle is in motion could result in an accident.
Practice good common sense when using your Lightfilm™ device and remember the following tips:
- DO NOT ADJUST PRODUCT WHILE DRIVING.
Do not attempt to touch or adjust your Lightfilm™ products while driving. This will distract you and cause your attention to be diverted from watching the road and overall safe driving.
- GET TO KNOW YOUR LIGHTFILM™ PRODUCT.
Before using your product, get to know its features and method of use. Understand how the product is attached to a car window.
- DO NOT BLOCK YOUR CLEAR VIEW OF THE ROAD.
It is the sole responsibility of the owner/user of Lightfilm™ products to place and secure Lightfilm™ products so that it does not interfere with vehicle operating controls or obstruct the driver’s clear view of the road. After placing your Lightfilm™ product on your motor vehicle’s window, sit in the driver’s seat before starting your car to ensure that your view is not blocked in any way. If your view is obstructed, you must move the Lightfilm™ product to a position that does not obstruct your clear view of the road. This is not only a critical safety step, but may also be required to comply with state and local laws concerning signage in your motor vehicle.
- DO NOT USE ANY LIGHTFILM™ DEVICE TO IMPERSONATE AN EMERGENCY VEHICLE.
Other Important Safety Information
- Check to make sure that your Lightfilm™ product is mounted and operating properly before driving.
- Do not store or carry flammable liquids, gases or explosive materials in the same compartment as the Lightfilm™ product, its parts or accessories.
- For vehicles equipped with an air bag, remember that an air bag inflates with great force. Do not place the Lightfilm™ product, power cord(s), controller or its accessories in the area over the air bag or in the air bag deployment area. If the Lightfilm™ product is improperly installed and the air bag inflates, serious injury could result
ALL INFORMATION SUBJECT TO CHANGE |
